Version 3.1.6 - 03.26.2023
- Added inclined walls for all wall types: rectangular, shed, gable and hip.









This new feature can also be used on CMU, ICF and CMU CORE walls.

That's the thing...I'm the builder.  I also have no construction experience and am essentially learning as I go and I'm doing all the prep I can now before I start building in about 3 months.

I was thinking about doing a "flat" roof, however thinkin about how I would make the deck, I think I might go with a traditional gable where its higher in the center. Reason being that would lower the sides of the house/trailer which would allow for the 2x4/2x6 that run the perimeter for the deck boards to attach to, to be sunk lower in hopes that I will only lose ceiling height of about 2-3 inches (just enough room for the deck boards and maybe a slight space between the top of roof and bottom of deck boards.

I thought I would circle back to inclined walls since I had some questions on shed dormers over the weekend.

I've updated the wall menus to include these new parameters now I just need to create the boolean logic to modify the wall geometry accordingly:



This feature should give the user the flexibility to modify rectangular, hip, shed or gable walls as needed when an inclined bottom plate is required.

I know this thread is pretty much from a year ago, but I too am glad this forum still exists and hasn't been absorbed into some sort of fakebook group. 

Really appreciate the resource and I still think the majority of archived content continues to be relevant. Thanks!

OK. Had no idea it was being prebuilt.

Will it have a flat roof as made by the builder? If so ask them about using the roof as a deck? (just covering all bases as you did not indicate)

https://www.youtube.com/watch?v=7Yo_7uKcFYw

This is a good example 

Quote from: MountainDon on March 21, 2023, 02:38:48 PMSo this is an enclosed trailer, sorta like a cargo trailer but built on a gooseneck chassis?  If so, ask the constructor how to best safely attach to the shell structure he builds.

If you mean you want to take a flat deck equipment gooseneck trailer and build a house structure on it yourself I personally would rethink that whole idea. I believe the weight would get very heavy if the entire shell was built from wood. Plus welded steel tubing is better suited to a mobile structure. (or aluminum tubing if done by a certified aluminum welder.)

Perhaps I don't fully understand the purpose and what/how you wish to do this?

It's a Tiny house on wheels (THOW). It's a pretty commonplace concept now with hundreds of gooseneck specific tiny houses available on youtube to check out. The house is built directly on the gooseneck trailer as the foundation. Several different ways to tie/secure it to the frame. I'll also be adding 3 or 4 pieces per side of all one piece all-thread that will go from below the trailer up the entire wall and mount on the top plate. 

Not so worried about the house itself, but the deck on top of the house. 

I would add another midspan post under the new load bearing walls to shorten thar span. I actually think it would be good to nail the rafters into the deckboards -- think of them as the joists preventing spreading or compression. Also if the deck is attached to your house with a ledger I would think about sticking a post or pilaster under the load bearing ends against the wall.

Nice A-frame.

I would consider installing a horizontal run of rope anchors (screw hooks?) just beneath the upper window.  Install a matching set of anchors on the outer hand rail.  Install a (rope reinforced?) rectangular sheet of heavy tarp... just for the season.  This inclined plane should keep much of your porch area free of snow, snow that now gets dumped beyond the hand rail.  Probably will require a "thumping" underneath after each snowfall.  ??

So this is an enclosed trailer, sorta like a cargo trailer but built on a gooseneck chassis?  If so, ask the constructor how to best safely attach to the shell structure he builds.

If you mean you want to take a flat deck equipment gooseneck trailer and build a house structure on it yourself I personally would rethink that whole idea. I believe the weight would get very heavy if the entire shell was built from wood. Plus welded steel tubing is better suited to a mobile structure. (or aluminum tubing if done by a certified aluminum welder.)

Perhaps I don't fully understand the purpose and what/how you wish to do this?